Netgate is offering COVID-19 aid for pfSense software users, learn more.
Connecting to Cisco IOS Devices with IPsec¶
This page describes how to configure IPsec to connect pfSense® router and a Cisco IOS router with IPsec capabilities.
This diagram shows the specifics of the network where this VPN is being configured. For the sake of this documentation, both hosts were on private subnets, but functionally equivalent to two hosts across the Internet.
Configuring the router¶
First, configure the phase 1 settings with a crypto isakmp policy. The following sets it for 3DES, SHA and group 2 to match the pfSense configuration shown later.
crypto isakmp policy 10 encr 3des authentication pre-share group 2
Next, configure the pre-shared key. The key in this example is ABCDEFG, but be sure to use something random and secure for any production deployments. 10.0.66.22 is the WAN IP of the pfSense system being used.
crypto isakmp key ABCDEFG address 10.0.66.22 no-xauth
Next configure the transform set for phase 2. This uses ESP, 3DES and SHA. The transform set is named 3DES-SHA, which is how it will be referred to later.
crypto ipsec transform-set 3DES-SHA esp-3des esp-sha-hmac
Now configure an access list that will match the local and remote subnets on the pfSense router. This is configured as access-list 100, which will be used in the next step. Remember this uses wildcard masks, so a /24 network (255.255.255.0 mask) is represented as 0.0.0.255.
access-list 100 permit ip 192.168.11.0 0.0.0.255 172.26.5.0 0.0.0.255 access-list 100 permit ip 172.26.5.0 0.0.0.255 192.168.11.0 0.0.0.255
Now configure the crypto map for this VPN:
crypto map PFSVPN 15 ipsec-isakmp set peer 10.0.66.22 set transform-set 3DES-SHA set pfs group2 match address 100
Lastly, under the interface configuration for the interface where the VPN will terminate (the one with the public IP), assign the crypto map:
interface FastEthernet0/0 crypto map PFSVPN
The configuration is then finished on the Cisco side.
Configuring pfSense Software¶
This screenshot shows the pfSense configuration matching the above Cisco configuration.
In the above example, the pfSense IPsec tunnel should be set as follows:
Remote Gateway: 10.0.64.175 Authentication Method: Pre-Shared Key Negotiation Mode: Main My Identifier: My IP Address Pre-Shared Key: ABCDEFG Encryption Algorithm: 3DES Hash Algorithm: SHA1 DH Key Group: 2 Lifetime: 28800 NAT Traversal: Disable
It may also be advisable to set Proposal Checking to Obey to avoid some issues with building a tunnel when the other side initiates.
Mode: Tunnel IPv4 Local Network: LAN Subnet Remote Network: 172.26.5.0/24 Protocol: ESP Encryption Algorithm: 3DES (others may also be checked, but be sure to leave 3DES checked) Hash Algorithm: SHA1 PFS Key Group: 2 Lifetime: 3600
Testing the connection¶
To test the connection, from the pfSense router, do the following:
Navigate to Diagnostics > Ping
Enter an IP address on the remote network
Choose the LAN interface
The initial negotiation may make all three of the first pings timeout, so try it a second time as well. If configured as depicted above, once the tunnel connects, the following will be seen:
If the connection doesn’t come up, there is a mismatch somewhere in the configuration. Depending on specifics, more useful information may be obtained from pfSense router or the Cisco router. Checking logs on both ends is recommended. For pfSense software, browse to Status > System Logs on the IPsec tab. For Cisco, run debug crypto isakmp and term mon (if not connected via serial console) to make the debug messages appear in a session. The output can be verbose, but will usually tell specifically what was mismatched.
“No NAT” List on Cisco IOS¶
It may also be necessary to tell Cisco IOS not to NAT the traffic that is destined for the IPsec tunnel. There are several ways to accomplish this, depending on how the router has NAT configured. If the following example does not help, there are several examples that turn up in a Google search for “cisco ios nonat ipsec”:
ip nat inside source route-map NONAT interface FastEthernet0/0 overload access-list 110 deny ip 172.26.5.0 0.0.0.255 192.168.11.0 0.0.0.255 access-list 110 permit ip 172.26.5.0 0.0.0.255 any route map NONAT permit 10 match ip address 110
This will direct the router to prevent NAT if the traffic is going from the subnet behind the Cisco router to the subnet behind the pfSense router, but allow it in all other cases.