M.2 NVMe SSD Installation

The Netgate® 8200 ships with a a PCIe-based M.2 NVMe drive, but users may wish to replace this storage, for example, with a larger capacity drive.

Warnings and Precautions

Danger

Anti-static protection must be used throughout this procedure.

Warning

The Netgate 8200 only supports PCIe-based M.2 NVMe storage devices. It does not support M.2 SATA devices.

The Netgate 8200 has one socket capable of supporting a PCIe-based M.2 NVMe drive. This is a B-key socket which accepts M.2 B+M-key or B-key PCIe NVMe SSDs only.

Danger

Take all appropriate precautions and exercise care when handling the exposed system board and M.2 card. There are many delicate components which can be damaged during this process. Damage caused via physical contact and electrostatic discharge while performing this installation is not covered by the warranty.

Required Tools and Hardware

Installing an M.2 NVMe SSD in the Netgate 8200 requires the following tools and hardware:

• #1 Phillips screwdriver

• T10 Torx driver

• T6 Torx driver

• Anti-static grounding strap and anti-static mat for handling bare M.2 card and 8200 system

• 1 x PCIe-based M.2 NVMe SSD, 2242 or 2280 size, B+M-key or B-key card

Installation Procedure

The installation procedure has many steps which are broken down into related groups in the remainder of this document. Follow all steps in the procedure carefully.

Take a Backup

If the system contains an existing configuration which should be carried over to the new SSD, then the first step is to take a backup of that configuration.

If the existing configuration is not necessary, this section may be skipped.

There are numerous backup options covered in the pfSense software documentation section on Backup and Restore.

For the purposes of reinstalling and restoring, the easiest method is to take a local backup.

Download the Installer

Before proceeding further, download a copy of the Netgate Installer amd64 memstick image using a Netgate Store Account and write the installer to a USB memstick. For details, see Reinstalling pfSense Plus Software.

Power Off and Disconnect

Installing the SSD requires removing the top of the case to expose the internal components. Before opening the case, the Netgate 8200 must be completely disconnected from everything. This includes power, network cables, USB cables, serial console cables, and any other cable or devices connected to the Netgate 8200.

Danger

Reminder:

• Anti-static protection must be used throughout this procedure.

• Any hardware damage incurred during this procedure is not covered by the hardware warranty.

1. Unplug the power cable

   Danger

   Wait at least 60 seconds after unplugging power to proceed. This ensures that all phantom power has dissipated.

2. Unplug all network cables, USB cables and devices, serial console connections, etc.

3. Dismount the Netgate 8200 device (e.g. remove from the Netgate 8200 Rack Mount)

4. Move the Netgate 8200 to a safe work location such as an anti-static mat

Removing the Lid

The next portion of the procedure involves opening the device and removing the lid.

Danger

Reminder:

• Anti-static protection must be used throughout this procedure.

• Any hardware damage incurred during this procedure is not covered by the hardware warranty.

1. Turn the device over carefully and protect the surface to avoid damaging the lid of the device

   Tip

   An anti-static mat or similar non-marring work surface is ideal for this role.

2. Locate and remove the eight (8) T10 Torx and two (2) T6 Torx screws holding the chassis together using appropriately sized Torx drivers.

   

   Netgate 8200 case screw locations

3. Gently remove the bottom panel.

   Tip

   This is a good opportunity to gently clean any dust and debris out of the fan and fan duct slots.

   

   Netgate 8200 with bottom panel removed

4. Turn the device so the I/O panel (“rear” of the system) is visible.

5. Gently pull the edge of the plastic lid at the right corner of the device away from the base only far enough for the lid to clear the the SIM card slots.

   

   Removing the lid while clearing the SIM card slots

6. Separate the remainder of the lid from the chassis and system board.

   

   Removing the Netgate 8200 chassis from the lid

7. Set the lid off to the side, keeping it upright to avoid damaging the top surface.

8. Turn the chassis upright so that the system board is visible.

9. Set the upright system flat on its base.

10. Turn the device so the I/O panel (“rear” of the system) is visible.

Install the SSD

Now that the lid is removed, it is time to install the SSD.

Danger

Reminder:

• Anti-static protection must be used throughout this procedure.

• Any hardware damage incurred during this procedure is not covered by the hardware warranty.

1. Locate the M.2 socket in which the M.2 NVMe SSD is installed.

   With the device in the proper orientation, it is approximately halfway up the left side of the board.

2. Remove the retention screw from the SSD standoff using the #1 Phillips head screwdriver.

3. Gently lift the current M.2 card up to approximately a 30° angle then remove it from the socket.

   

   Netgate 8200 top-down internal view

4. Move the standoff to the appropriate hole for the new SSD length (2242 or 2280) if it is not already in the correct location.

5. Insert the new M.2 card into the socket at an approximate 30° angle.

   Note

   As mentioned earlier in this document, the Netgate 8200 currently supports M.2 B+M-key or B-key PCIe NVMe SSDs only.

   Warning

   M.2 cards are keyed. Do not force an M.2 card into a slot with mismatched keying.

   Refer to M.2 Edge Connector Keying for a depiction of the different M.2 key types.

6. Gently push down the M.2 NVMe card until it reaches the standoff.

7. Insert the retention screw into the standoff and tighten using the #1 Phillips head screwdriver.

   

   2280 length M.2 NVMe SSD installed and secured with retention screw

Replacing and Fastening the Lid

With the M.2 NVMe SSD in place, the next step is to replace the lid and all of the fasteners.

Danger

Reminder:

• Anti-static protection must be used throughout this procedure.

• Any hardware damage incurred during this procedure is not covered by the hardware warranty.

1. Align the USB ports on the left side with the matching holes in the lid.

2. Align the internal groove in the lid with the edges of the I/O panel.

3. Lower the left edge of the lid onto the chassis.

   

   Aligning the left edge of the lid with the USB ports and I/O panel

4. Continue lowering the chassis until the lid until the right side is at the edge of the lid.

5. Gently pry the right side of the lid away from the chassis enough to clear the SIM card slots while simultaneously lowering the chassis.

   The lid should click into place over the SIM card slots.

   

   Replacing the lid while clearing the SIM card slots

6. Check the rear corners of the lid to make sure the I/O panel is fully seated in the lid grooves.

7. Check the alignment of the plastic lid edges with the metal base plate, SIM card slots, USB A opening, etc.

8. Replace the bottom panel.

9. Replace the eight (8) T10 Torx and two (2) T6 Torx screws holding the chassis together using appropriately sized Torx drivers.

   

   Netgate 8200 case screw locations

Reconnect

The device is now ready to be put back into its former location.

1. Move the device back to its original location.

2. Re-mount the Netgate 8200 device (e.g. put it back in the Netgate 8200 Rack Mount)

3. Plug in all network cables, USB cables and devices, serial console connections, etc.

4. Insert the USB memstick containing the installation media

5. Plug in the power cable

6. Reconnect to the serial console

Reinstall pfSense Plus Software

With the device back together and ready to proceed, the next step is to reinstall pfSense Plus software to the SSD. This procedure is covered in detail in Reinstalling pfSense Plus Software.

Note

If prompted to select a drive during the installation, choose the NVMe drive which will be nda0. The installer will typically select this drive automatically, but double check to be certain it is correct.

If there is no backup to restore, then no further steps are necessary. Login to the firewall and configure it as normal (Initial Configuration).

Restore the Configuration

The final step is to restore the configuration. If a configuration was backed up earlier in this procedure, now is the time to restore it using the GUI or one of the other methods mentioned in the pfSense software documentation section on Backup and Restore.