Tip

This is the documentation for the 19.05 version. Looking for the documentation of the latest version? Have a look here.

Troubleshooting¶

This section contains commonly encountered issues with TNSR and methods to resolve them.

Ping and traceroute do not function without host OS default route
Unrecognized routes in a routing table
Services do not receive traffic on an interface with NAT enabled
NAT session limits / “Create NAT session failed” error
ACL rules do not match NAT traffic as expected
Some Traffic to the host OS management interface is dropped
Locked out by NACM Rules
How to gain access to the root account
Console Messages Obscure Prompts
Diagnosing Service Issues
Debugging TNSR

Ping and traceroute do not function without host OS default route ¶

Utilities such as ping and traceroute will send traffic using the host OS routing table by default unless a specific source address is passed to the command. See Diagnostic Routing Behavior for details.

Unrecognized routes in a routing table ¶

TNSR automatically populates routing tables with necessary entries that may not appear to directly correspond with manually configured addresses. See Common Routes for details.

Services do not receive traffic on an interface with NAT enabled ¶

When NAT is enabled, by default TNSR will drop traffic that doesn’t match an existing NAT session or static NAT rule. This includes traffic for services on TNSR such as IPsec and BGP. To allow this traffic, see NAT Forwarding.

NAT session limits / “Create NAT session failed” error ¶

By default the dataplane limits the number of NAT sessions for an IP address to a relatively low number (100) based on the configured value for dataplane nat max-translations-per-user. This can be changed as described in Advanced Dataplane Configuration: NAT:

ACL rules do not match NAT traffic as expected ¶

When NAT is active, ACL rules are always processed before NAT on interfaces where NAT is applied, in any direction. This behavior is different from some other products, such as pfSense. See ACL and NAT Interaction for details.

Some Traffic to the host OS management interface is dropped ¶

TNSR includes a default set of Netfilter rules which secure the management interface. Only certain ports are allowed by default. See Default Allowed Traffic for details. To allow more traffic, create host ACLs as described in Host ACLs.

Locked out by NACM Rules ¶

If TNSR access is lost due to the NACM configuration, access can be regained by following the directions in Regaining Access if Locked Out by NACM.

How to gain access to the root account ¶

By default, the root account has interactive login disabled, which is the best practice. This can be changed by resetting the root password using sudo from another administrator account, or in the ISO installer. See Default Accounts and Passwords for details.

Console Messages Obscure Prompts ¶

When connected to the console of a TNSR device, such as the serial console, the kernel may output messages to the terminal which obscure prompts or other areas of the screen. This is normal and an expected effect when using the console directly.

To work around this intended behavior, use one of the following methods:

Press Ctrl-L to clear or redraw the screen without the messages.
Press Enter to receive a new prompt.
Run sudo dmesg -D from a shell prompt or with the TNSR shell command, which will disable kernel output to all consoles.
Connect to the TNSR device using SSH instead of the console.

Diagnosing Service Issues ¶

If a service will not stay running and the logs indicate that it is crashing, additional debugging information can be obtained from core dumps.

By default, core dumps are disabled for services. These can be individually enabled as needed by the following command:

tnsr(config)# service (backend|bgp|dataplane|dhcp|http|ike|ntp|restconf|unbound)
                 coredump (enable|disable)

The resulting core files will be written under /var/lib/systemd/coredump/.

Debugging TNSR ¶

The following commands enable debugging information in various aspects of TNSR. These should only be used under direction of Netgate.

debug cli [level <n>]

Enable debugging in clixon and cligen at the given level.

debug tnsr (clear|set|value) <flags>

Enable debugging in TNSR. The set or clear command may be repeated multiple times to add or remove individual flag values. The value command may be used to directly set the value. The <flags> value is the logical or of all desired debugging flags.

The following flag values are available:

Flag	Value
TDBG_NONE	0x00000000
TDBG_FRR	0x00000001
TDBG_HOST	0x00000002
TDBG_KEA	0x00000004
TDBG_VPP	0x00000008
TDBG_NTP	0x00000010
TDBG_STRONGSWAN	0x00000020
TDBG_UNBOUND	0x00000040
TDBG_HTTP	0x00000080
TDBG_DELAYED_NODE	0x00001000
TDBG_DEP_GRAPH	0x00002000
TDBG_TRANSACTION	0x00004000
TDBG_ACL	0x00010000
TDBG_BGP	0x00020000
TDBG_BRIDGE	0x00040000
TDBG_INTF	0x00080000
TDBG_NEIGHBOR	0x00100000
TDBG_SUBIF	0x00200000
TDBG_SYSCTL	0x00400000
TDBG_GRE	0x00800000
TDBG_LOOPBACK	0x01000000
TDBG_ROUTE	0x02000000
TDBG_SPAN	0x04000000
TDBG_MAP	0x08000000

debug vmgmt (clear|set|value) <flags>

Enable VPP Mgmt library debug. The set or clear command may be repeated multiple times to add or remove individual flag values. The value command may be used to directly set the value. The <flags> value is the logical or of all desired debugging flags.

The following flag values are available:

Flag	Value
VDBG_NONE	0x0000
VDBG_API_SETUP	0x0001
VDBG_API_MSG	0x0002
VDBG_ACL	0x0004
VDBG_BRIDGE	0x0008
VDBG_INTF	0x0010
VDBG_NAT	0x0020
VDBG_TAP	0x0040
VDBG_MEMIF	0x0080
VDBG_LLDP	0x0100
VDBG_GRE	0x0200
VDBG_MAP	0x0400
VDBG_ROUTE	0x0800

no debug (cli|tnsr|vmgmt)

Removes all debugging.