This is the documentation for the 21.07 version. Looking for the documentation of the latest version? Have a look here.
Commands in this section configure hardware settings for DPDK devices.
- dataplane dpdk dev <pci-id> (crypto|crypto-vf)
- dataplane dpdk dev (<pci-id>|<vmbus-uuid>) network [name <name>] [num-rx-queues [<rq>]] [num-tx-queues [<tq>]] [num-rx-desc [<rd>]] [num-tx-desc [<td>]] [tso (off|on)] [vlan-strip-offload (off|on)]
Configures a manually approved list of network interface PCI devices or Hyper-V/Azure VMBUS device UUIDs and their options. Typically the dataplane will automatically attempt to use eligible interfaces, but this command overrides that behavior by explicitly listing devices which will be used by the dataplane.
See Setup NICs in Dataplane for more information and examples for adding devices in this manner.
Adding devices in this way is not compatible with
dataplane dpdk blacklist, but when devices are listed manually via
dataplane dpdk devdenying in that way is unnecessary.
- name <name>
Sets a custom name for a network device in TNSR instead of the automatically generated name (
<Link Speed><Bus Location>). For example device
0000:06:00.0can have a custom name of
WANinstead of the default
GigabitEthernet6/0/0. Used for convenience and to make interface names self-documenting.
See Customizing Interface Names for additional details.
- num-rx-queues [<rq>] num-tx-queues [<tq>]
Receive and transmit queue sizes for this device.
- num-rx-desc [<rd>] [num-tx-desc [<td>]
Receive and transmit descriptor sizes for this device. Certain network cards, such as Fortville models, may need the descriptors set to
2048to avoid dropping packets at high loads.
- tso (on|off)
TCP segmentation offload (TSO). When enabled on hardware which supports TSO, packet data is offloaded to hardware in large quantities and the hardware handles segmentation into MTU-sized chunks rather than performing segmentation in software. This results in improved throughput as shifting the per-packet processing to hardware reduces the burden on the network stack. Disabled by default.
- vlan-strip-offload (off|on)
Enables hardware offloading of VLAN stripping. This utilizes hardware filtering of VLAN packets which are not destined for VLANs configured on TNSR. Improves performance by reducing processing of irrelevant packets when connected to switch trunking ports. Disabled by default.
The default values for these configuration options can be set by
dataplane dpdk dev default network <options>. These default values are used by the dataplane when an interface does not have a specific value set. The
nameoption must be unique for each interface and thus does not support a default value.
- dataplane dpdk blacklist <vendor-id>:<device-id>
Prevents the dataplane from automatically attaching to any device which matches a specific PCI vendor and device identifier. Useful for preventing the dataplane from attaching to hardware devices which are known to be incompatible.
Listing devices in this way is not compatible with
dataplane dpdk dev.
- dataplane dpdk blacklist (<pci-id>|<vmbus-uuid>)
Similar to the previous form, but explicitly prevents the dataplane from attaching to a specific PCI device or Hyper-V/Azure VMBUS device UUID.
Listing devices in this way is not compatible with
dataplane dpdk dev.
- dataplane dpdk decimal-interface-names
Disabled by default. When set, interface names automatically generated by the dataplane will use decimal values for bus location values rather than hexadecimal values. Linux uses decimal values when forming interface names (e.g.
enp0s20f1), so administrators may find using decimal values more familiar.
For example, device ID
enp0s20f1in the host OS) would normally be
GigabitEthernet0/14/1since the value
14in the bus slot is in hexadecimal. With
decimal-interface-namesset, the name would be
- dataplane dpdk iova-mode (pa|va)
Manually configures the IO Virtual Addresses (IOVA) mode used by DPDK when performing hardware IO from user space. Hardware must use IO addresses, but it cannot utilize user space virtual addresses directly. These IO addresses can be either physical addresses (PA) or virtual addresses (VA). No matter which mode is set, these are abstracted to TNSR as IOVA addresses so it does not need to use them directly.
In most cases the default IOVA mode selected by DPDK is optimal.
vfio-pciUIO driver is active, IOVA must be explicitly set to
pasince the automatic selection of
vawill fail with that driver.
For more detail on IOVA, consult the DPDK documentation.
Physical Address mode. IOVA addresses used by DPDK correspond to physical addresses, and both physical and virtual memory layouts match. This mode is safest from the perspective of the hardware, and is the mode chosen by default. Most hardware supports PA mode at a minimum.
The primary downside of PA mode is that memory fragmentation in physical space must also be reflected in virtual memory space.
Virtual Address mode. IOVA addresses do not follow the layout of physical memory; Physical memory is changed to match the virtual memory instead. Because virtual memory appears as one continuous segment, large memory allocations are more likely to succeed.
The primary downside of VA mode is that it relies on kernel support and the availability of IOMMU.
- dataplane dpdk log-level (alert|critical|debug|emergency|error|info|notice|warning)
Sets the log level for messages generated by DPDK. The default log level is
- dataplane dpdk no-multi-seg
Disables multi-segment buffers for network devices. Can improve performance, but disables jumbo MTU support.
Required for Mellanox devices.
This option is not currently compatible with Intel X552 10G network interfaces. When enabled on incompatible hardware this option can lead to instability such as dataplane crashes while under load.
- dataplane dpdk no-pci
Disables scanning of the PCI bus for interface candidates when the dataplane starts. By default, interfaces which are administratively down in the host OS can be selected for use by the dataplane.
- dataplane dpdk no-tx-checksum-offload
Disables transmit checksum offloading of TCP/UDP for network devices.
- dataplane dpdk num-mem-channels <num>
Sets the number of memory channels into the CPU. Optimal value varies by hardware specifications and number of installed memory modules. For example, a device with four memory modules installed may have
2memory channels. Check the BIOS and OEM hardware specifications to determine the value. Valid values are from
- dataplane dpdk tcp-udp-checksum
Enables receive checksum offloading of TCP/UDP for network devices. Disabled by default.
- dataplane dpdk num-crypto-mbufs <num>
Sets the number of memory buffers used by the dataplane for cryptographic tasks, in the range
1-4294967295. Higher values can improve throughput when the dataplane encrypt/decrypt nodes are processing data.
- dataplane dpdk uio-driver [<driver-name>]
Configures the UIO driver for interfaces. See Setup NICs in Dataplane.