Tip

This is the documentation for the 19.08 version. Looking for the documentation of the latest version? Have a look here.

Setup QAT Compatible Hardware

TNSR Supports hardware compatible with Intel® QuickAssist Technology, also known as QAT, for accelerating cryptographic and compression operations.

This hardware can be found in CPIC cards as well as many C3000 and Skylake Xeon systems. Netgate XG-1541 and XG-1537 hardware has an add-on option for a CPIC card.

Setup Process

Enable SR-IOV in the BIOS

SR-IOV is required for QAT to function in TNSR. SR-IOV enables Virtual Functions which are required for binding by crypto devices.

The procedure to enable SR-IOV varies by platform. Generally this involves rebooting the hardware and entering the BIOS setup, making the change, and then saving and rebooting. The exact location of the SR-IOV option also varies in different BIOS implementations.

Note

Netgate devices which ship with a CPIC card preinstalled will have this step completed at the factory, but double check the BIOS to ensure it is set as expected.

Enable IOMMU in grub

IOMMU (Input–Output Memory Management Unit), which in this context is also known as Intel VT-d, must be enabled in grub for QAT to function. It functions similar to PCI passthrough, allowing the dataplane to access the QAT device.

To enable IOMMU in grub:

  • Open /etc/default/grub in a text editor (as root or with sudo)

  • Locate the line starting with GRUB_CMDLINE_LINUX

  • Check if that line includes intel_iommu=on iommu=pt

  • If those parameters are not included on the line, append them to the end, before the end quote.

  • Save and exit the text editor

  • Run one following commands (depending on how the device boots):

    • Legacy: sudo grub2-mkconfig -o /boot/grub2/grub.cfg

    • UEFI: sudo grub2-mkconfig -o /boot/efi/EFI/centos/grub.cfg

  • Reboot the device

Change the uio driver to igb_uio

Next, change the TNSR dataplane uio driver to igb_uio:

tnsr# configure
tnsr(config)# dataplane dpdk uio-driver igb_uio

Configure the QAT PCI device in TNSR

Next, configure the QAT device in TNSR.

To configure this device, first locate its PCI ID. TNSR will print the PCI ID when viewing possible parameters for dataplane devices

tnsr(config)# dataplane dpdk dev ?
0000:03:00.0           Ethernet controller: Intel Corporation Ethernet Connection X552 10 GbE SFP+
0000:03:00.1           Ethernet controller: Intel Corporation Ethernet Connection X552 10 GbE SFP+
0000:04:00.0           Co-processor: Intel Corporation DH895XCC Series QAT
0000:05:00.0           Ethernet controller: Intel Corporation I350 Gigabit Network Connection (rev 01) ( Active Interface eno1 )
0000:05:00.1           Ethernet controller: Intel Corporation I350 Gigabit Network Connection (rev 01)

In this instance, the following line from the output is for the QAT device:

0000:04:00.0 Co-processor: Intel Corporation DH895XCC Series QAT

The first value printed on the line is the PCI ID, 0000:04:00.0.

Now, tell TNSR the device at that address is a crypto device:

tnsr(config)# dataplane dpdk dev 0000:04:00.0 crypto

Activate and check the settings

When viewing the XML configuration with show configuration running, it will contain settings similar to the following example. Note that if other dataplane options are present in the configuration, those will also be visible. Here is how it looks once configured:

<dataplane-config>
   <dpdk>
      <dev>
         <id>0000:04:00.0</id>
         <device-type>crypto</device-type>
      </dev>
      <uio-driver>igb_uio</uio-driver>
   </dpdk>
</dataplane-config>

After configuring the crypto device and uio driver, TNSR will commit the settings to the dataplane configuration.

To activate the new settings, restart the dataplane.

tnsr(config)# service dataplane restart
tnsr(config)# exit
tnsr#

Lastly, using the shell command, verify that VPP can see the crypto device:

tnsr# shell sudo vppctl show dpdk crypto devices
0000:04:00.0_qat_sym     crypto_qat          up
  numa_node 0, max_queues 2
  free_resources 0, used_resources 1
  SYMMETRIC_CRYPTO, SYM_OPERATION_CHAINING, HW_ACCELERATED, IN_PLACE_SGL, OOP_SGL_IN_SGL_OUT, OOP_SGL_IN_LB_OUT, OOP_LB_IN_SGL_OUT, OOP_LB_IN_LB_OUT
  Cipher: none, aes-cbc-128, aes-cbc-192, aes-cbc-256, aes-ctr-128, aes-ctr-192, aes-ctr-256, aes-gcm-128, aes-gcm-192, aes-gcm-256
  Auth: none, md5-96, sha1-96, sha-256-96, sha-256-128, sha-384-192, sha-512-256

Troubleshooting

If the QAT device does not appear in the show dpdk crypto devices output, or it only shows an AES-NI device, then VPP can not see the crypto device. To correct this, first verify the QAT drivers are loaded, VFs exist for the QAT device, and grub BOOT_IMAGE is passing the necessary iommu parameters.

Verify IOMMU parameters:

$ dmesg | grep iommu

The following parameters should appear somewhere on the BOOT_IMAGE line in the dmesg output:

intel_iommu=on iommu=pt

Verify that the QAT drivers are loaded in the operating system:

$ lsmod | grep qat
qat_dh895xccvf         13281  0
qat_dh895xcc           13510  0
intel_qat             141755  2 qat_dh895xccvf,qat_dh895xcc
dh_generic             13286  1 intel_qat
rsa_generic            18819  1 intel_qat
authenc                17776  1 intel_qat

Verify Virtual Functions (VFs) exist for the QAT device:

$ lspci | grep QAT | wc -l

The number of listings are dependent on how many threads VPP uses to process packets. At minimum there will be at least three entries, but there may be many more. The lines will look similar to this example:

04:00.0 Co-processor: Intel Corporation DH895XCC Series QAT
04:01.0 Co-processor: Intel Corporation DH895XCC Series QAT Virtual Function
04:01.1 Co-processor: Intel Corporation DH895XCC Series QAT Virtual Function

TNSR stores the device Physical Function (PF), 04:00.0 for example, in its configuration because the VFs do not yet exist at boot time. They are created by clixon-backend when it processes the crypto device. Then, the allocated VFs on the PF have their addresses written to startup.conf.

The VFs are bound to igb_uio because igb_uio is a driver which allows a userspace process to do RDMA on buffers that are used by a PCI device.

If the drivers are loaded and the VFs show under lspci, then verify /etc/vpp/startup.conf has the appropriate dpdk settings. The igb_uio driver must be present and the PCI IDs of TNSR interfaces along with one of the VFs for the QAT device:

dpdk {
    uio-driver igb_uio
    dev 0000:04:01.0
    dev 0000:05:00.1
    dev 0000:03:00.0
    dev 0000:03:00.1
}

If that looks correct, verify igb_uio is being used by the QAT VF and interfaces:

$ sudo vppctl show pci all | grep igb_uio
0000:03:00.0   0  8086:15ac   2.5 GT/s x1  igb_uio
0000:03:00.1   0  8086:15ac   2.5 GT/s x1  igb_uio
0000:04:01.0   0  8086:0443   unknown      igb_uio
0000:05:00.1   0  8086:1521   5.0 GT/s x4  igb_uio

Physical TNSR interfaces will display there in addition to the QAT VF ID, which matches the QAT VF ID configured for dpdk in /etc/vpp/startup.conf.

If any of those tests do not provide the expected output, then reboot the system and check again. Ensure the TNSR services and VPP are running, and then check the VPP QAT status again.

$ sudo vppctl show dpdk crypto devices

If there is still no output, verify the PCI ID for the crypto device specified in TNSR is accurate. It must be the first PCI ID displayed by lspci | grep qat. Then verify the PCI ID of the next listing in that output (first VF device) is specified in /etc/vpp/startup.conf properly and also the same PCI ID seen by VPP when running:

$ sudo vppctl show pci all | grep igb_uio