Tip

This is the documentation for the 20.02 version. Looking for the documentation of the latest version? Have a look here.

TNSR 19.02 Release Notes

About This Release

Warning

A number of commands were reorganized with this release, more information will be noted below in individual sections. If a command that worked in a previous release is no longer present, it has most likely been changed to a more logical and consistent location.

Warning

RESTCONF queries now require a namespace in the format of module:name where only the name was required in previous versions. To locate the correct module:name combination, see API Endpoints.

General

  • The data models have been updated with more consistent naming and locations

  • Introduced a YANG id type for name fields [1318]

  • Miscellaneous code cleanup and refactoring for stability and performance improvements [1516] [1571]

  • Updated to CentOS 7.6 [1335]

  • Updated build to use gcc 7 [1147]

  • Fixed a potential crash when listing packages [1312]

  • Improved handling of package versions to better handle situations where a dependency update requires reinstalling related packages [950]

BGP

  • BGP commands reorganized under route dynamic for configuration and show route dynamic for status. See Commands and Border Gateway Protocol. [1369]

  • FRR updated to 6.0.x

CLI

  • The configuration database commands have been reorganized under configuration for making changes, such as copy, and under show configuration for viewing the contents of a configuration. See Commands and Configuration Database. [1347]

  • Fixed system location text handling when the value contains whitespace [1584]

Dataplane

  • Updated DPDK igb_uio module to v19.02 [842]

DHCP Server

  • Updated Kea to 1.4.0-P1 [1239]

DNS

  • Fixed removal of access-control entries in the CLI [1417]

Host

  • Fixed inconsistent behavior of host interface commands [1611]

  • Added a default set of nftables rules to limit inbound traffic to the host [476]

Interfaces

  • Several interface-related configuration commands have been moved under the interface command for better consistency. These include: bridge, loopback, memif, subif, and tap. See Commands and Types of Interfaces [1336]

  • Added support for Bonding Interfaces for link aggregation and redundancy, including support for LACP [1025]

  • Fixed display of a single TAP interface [1554]

  • Fixed state data returned from a GET request for /netgate-interface:interfaces-state/interface [1553]

  • Corrected validation of memif socket ID to exclude 0 which is reserved, and enforce a maximum of 4294967294 [1527]

  • Corrected validation of bridge domain ID to exclude 0 which is reserved, and enforce a maximum of 16777215 [1526]

  • Fixed handling of non-default routing tables assigned to interfaces at startup [1518]

  • Removed unused container /interfaces-config/interface/tunnel from data model [1427]

  • Fixed subif commands outer-dot1q any and outer-dot1ad any [1552] [1352]

  • Fixed subinterfaces failing after changing configuration [1346]

  • Removed the untagged command from subif as it was non-functional and unnecessary (use the parent interface for untagged traffic) [1345]

NAT

RESTCONF

Warning

RESTCONF queries now require a namespace in the format of module:name where only the name was required in previous versions. To locate the correct module:name combination, see API Endpoints.

  • Fixed RESTCONF calls for RPCs returning error 400 despite succeeding [1511]

Routing

  • Fixed removing a route table reporting failure when the operation succeeded [1515]

Known Limitations

ACL

  • Attempting to create an ACL containing only a description fails [1558]

    Workaround: Define one or more rules on the ACL.

BFD

  • Attempting to change a BFD local/peer address fails [1549]

BGP

  • TNSR does not send BGP updates without restarting service with redistribute from connected option [746]

  • Route with aggregate-address via next-hop 0.0.0.0 does not appear in TNSR route table [832]

  • BGP sessions may fail to establish or rapidly reconnect when receiving more prefixes than defined by maximum-prefix limit [858]

  • The maximum-prefix restart command does not work [859]

  • TNSR installs multiple paths for received routes even though support for multiple paths is not enabled [885]

    Workaround: Run systemctl reset-failed frr from the shell to clear the error which will allow the BGP service to start again.

  • Changing update-source from an IP address to loop1 allows a session to establish but remote prefixes do not appear in the FIB until reboot [1104]

  • IPv6 BGP neighbors get entered as peer-groups only in bgpd.conf [1190]

  • BGP import-check feature does not work [781]

CLI

  • show route table causes the backend to die with large numbers of routes in the table [506]

    For example, this crash happens with a full BGP feed.

  • Using service dataplane restart can cause clixon_backend to lose its configuration [1383]

DHCP

  • DHCP server uses default VPP interface IP address (169.254.0.x) as a source address for DHCP packets and as a DHCP Server Identifier [1222]

  • Adding a DHCP reservation without a MAC address causes Kea to fail and the entry cannot be removed [1530]

    Workaround: A MAC address is required for DHCP reservations, so always enter a MAC address when creating an entry.

  • Configuring Kea to log all names with * does not work [1307]

    Workaround: Configure each name separately instead of using a wildcard.

DNS

  • Local zone FQDN handling for forward (A) and reverse (PTR) data is inconsistent, only allowing one or the other to work as expected for a given FQDN [1384]

HTTP Server / RESTCONF

  • nginx does not behave as expected with authentication type none and TLS [1086]

    This mode is primarily for testing and not production use.

    Workaround: Use password or certificate-based authentication for RESTCONF.

  • HTTP server runs even though it’s not configured to run after TNSR services restart [1153]

    Workaround: Manually stop the nginx service using systemctl.

  • RESTCONF get of /restconf/data/ does not properly return state data [1534]

  • RESTCONF query replies may contain CDATA tags in JSON [1463]

  • Adding an ACL rule entry via RESTCONF may appear to add a duplicate ACL [1238]

Interfaces

  • Loopback interface responds to ICMP echo from an outside host even when in a Down state [850]

  • Unable to delete an interface if has had an ACL or MACIP applied [1177, 1178]

    Workaround: Remove the entire ACL or MACIP entry. Then, the interface may be removed.

  • MACIP ACL remains in the interface configuration after being removed [1179]

  • Bond interfaces in LACP mode will send LACPDUs even when configured for passive mode [1614]

  • Non-LACP bond interfaces may experience packet drops when a bond member interface is down [1603]

  • MAC address change on tap interfaces may not be reflected in the dataplane until the dataplane is restarted [1502]

    Workaround: Restart the dataplane after changing an interface MAC address.

  • MAC address change on bond interfaces may not be reflected in the dataplane until the dataplane is restarted [1502]

    Workaround: Set the MAC address when creating the bond interface.

  • VLAN tag rewrite settings are only available in subinterfaces [1344]

  • Packets do not pass through a subinterface after the subinterface configuration has been modified [1612]

  • QinQ VLAN termination is not working [1550]

  • ARP replies received from another host on a VLAN subinterface are not processed correctly [1326]

IPsec

  • An IPsec tunnel which was removed and then added back in may take longer than expected to establish [1313]

NACM

  • Permitted default read and write operations cannot be executed if default exec policy is set to deny [1158]

NAT

  • twice-nat does not work [1023]

  • NAT mode is not deleted from VPP startup configuration after TNSR services restart [1017]

  • NAT forwarding is not working for in2out direction [1039]

  • NAT static mappings are not added as expected when only the port-local value differs [1100]

  • NAT static mapping with defined ports leads to clixon-backend crash after restart [1103]

  • DS-Lite is not functional; B4 router sends encapsulated IPv4-in-IPv6 packets, but AFTR replies with an error [1626]

  • DS-Lite B4 endpoint is not shown by show dslite command [1625]

  • Unable to view a list of NAT sessions [975, 1456]

Routing

  • Deleting a non-empty route table fails with an error and the table remains in the configuration, but it cannot be changed afterward [1241]

    Workaround: Remove all routes from the table before deleting. Alternately, copy the running configuration to startup and restart TNSR, which will make the route table appear again so the routes and then the table can be removed.

User Management

  • When deleting a user key from the running configuration it is not removed from the user’s authorized_keys file [1162]

    Workaround: Manually edit the authorized_keys file for the user and remove the key.

Reporting Issues

For issues, please contact the Netgate Support staff.